Kakute F4 V2.4 + Tekko32 F4 50A ESC Stack

- FC¿Í ESC ÄÞº¸ »óÇ°ÀÔ´Ï´Ù.

- Kakute F4 V2.4 FC¿Í Tekko32 F4 50A ESCÀÔ´Ï´Ù.

- MPU6000 ÀÚÀ̷θ¦ »ç¿ëÇÕ´Ï´Ù.

- BLHeli_32ºñÆ® Æß¿þ¾î¸¦ »ç¿ëÇÕ´Ï´Ù.

±¸¼º

ÇÏ´Ü »çÁø ÂüÁ¶

Description

The Holybro Kakute F4 V2.4 Flight Controller includes plug-and-play DJI O3 HD camera plug, 4in1 ESC ports, barometer, OSD,

5x UARTs, logging capability with built-in flash , 5V and 9V/3A BEC, easy soldering layout and much more.

The Kakute F4 V2.4 is DJI HD ready. It has an easy plug-and-play port with an on-board 9V/A regulator designed to power your HD video

transmitter like DJI O3 Air Unit & Caddx Vista while supporting analog system. It has 5x dedicated UART ports with built-in inversion for peripherals.

It is also ready for autonomous flight with the on-board barometer. There are LED & buzzer pad, I2C pad (SDA & SCL) for external GPS/Magnetometers.

Kakute F4 v2.4 FC Specification

MCU - STM32F405

IMU - MPU6000

Barometer - BMP280

OSD - AT7456E

5x UARTs (1,3,4,4,6,7)

128 Mbit Dataflash chip 

Battery input voltage: 2S-8S

BEC 9V/3A - Optimized for DJI O3 Air unit

BEC 5V/2A 

7x PWM Outputs (6 Motor Output, 1 LED)

Supports serial receivers (SBUS, iBus, Spektrum, Crossfire, ESLR).

Mounting - 30 x 30mm, ¥Õ4mm hole with M3 Grommets

Dimension - 37x37mm

Weight - 7g

JST-SH1.0_8pin port (For 4in1 ESCs)

JST-SH1.0_6pin port (For DJI/Caddx HD System and other VTX)

Tekko32 F4 4in1 50A ESC

Fast F4 MCU @150Mhz / PWM output up to 96K / 4~6S / BLHeli32 / 30x30

Features

New and faster F4 MCU @ 150Mhz (compared to F3 @108Mhz & F0 @48Mhz)

PWM Frequency: 16k to 96k

Separate drive & control circuit, this broadens the current capability of the drive circuit while reducing the electrical interference to the control circuit.

Specification

Continuous Current: 50A x4

Burst Current: 60A x4

Supports 4-6S battery

Supports DShot 150/300/600/1200 & MultiShot/OneShot/Proshot/PWM etc.

ESC telemetry Supported

Onboard analog current sensor

No output BEC

BLHeli_32 firmware

1000uf 35v capacitor included (highly recommended for 6s setup)

Amperage meter scale ratio: 120 (V1.9 Version)

Dimensions: 48x37x6mm / Weight: 13.8g

Mounting holes: M4 30.5x30.5mm (M3 grommets included)