Kakute H7 V1.3 + Tekko32 F4 50A ESC Stack

- FC¿Í ESC ÄÞº¸ »óÇ°ÀÔ´Ï´Ù.

- Kakute H7 V1.3 FC¿Í Tekko32 F4 50A ESCÀÔ´Ï´Ù.

- MPU6000 ÀÚÀ̷θ¦ »ç¿ëÇÕ´Ï´Ù.

- BLHeli_32ºñÆ® Æß¿þ¾î¸¦ »ç¿ëÇÕ´Ï´Ù.

±¸¼º

ÇÏ´Ü »çÁø ÂüÁ¶

Kakute H7 V1.3 FC Specification

MCU - STM32H743 32-bit processor running at 480 MHz 

• Professional underfill epoxy for mechanical reinforcement

IMU - MPU6000

Barometer - BMP280

OSD - AT7456E

Onboard Bluetooth chip - ESP32-C3  (Optional)

• SpeedyBee IOS & Android App Compatible 

• Note: The Bluetooth onboard is set to automatically turn off when the flight controller is unlocked (arm) and turn on automatically when the flight controller is locked (disarm) in Betaflight

6x UARTs (1,2,3,4,6,7; UART2 is used for Bluetooth telemetry)

9x PWM Outputs (8 Motor Output, 1 LED)

2x JST-SH1.0 8pin ESC port (4in1 ESCs, x8/Octocopter compatible)

1x JST-SH1.0 6pin VTX port (For HD System like Caddx Vista & Air Unit)

Battery input voltage: 3S - 8S

BEC 5V 2A Cont.

BEC 9V 3A Cont 

USB Type-C

Mounting - 30.5 x 30.5mm/¥Õ4mm hole with ¥Õ3mm Grommets

Dimension - 35x35mm

Weight - 8g

Firmware Targets

• BetaFlight: KakuteH7 (v4.2.11 & newer)

• INAV: KakuteH7 (4.0.0 & newer) SD card support added in 4.1.0.

• ArduPilot: KakuteH7 (4.2.0 & newer)

• PX4: KakuteH7 (PX4 v1.13 or newer)

Tekko32 F4 4in1 50A ESC

Fast F4 MCU @150Mhz / PWM output up to 96K / 4~6S / BLHeli32 / 30x30

Features

New and faster F4 MCU @ 150Mhz (compared to F3 @108Mhz & F0 @48Mhz)

PWM Frequency: 16k to 96k

Separate drive & control circuit, this broadens the current capability of the drive circuit while reducing the electrical interference to the control circuit.

Specification

Continuous Current: 50A x4

Burst Current: 60A x4

Supports 4-6S battery

Supports DShot 150/300/600/1200 & MultiShot/OneShot/Proshot/PWM etc.

ESC telemetry Supported

Onboard analog current sensor

No output BEC

BLHeli_32 firmware

1000uf 35v capacitor included (highly recommended for 6s setup)

Amperage meter scale ratio: 120 (V1.9 Version)

Dimensions: 48x37x6mm / Weight: 13.8g

Mounting holes: M4 30.5x30.5mm (M3 grommets included)